Learning the Basics of Plumbing for Bathtub Installation
Learning the Basics of Plumbing for Bathtub Installation
Blog Article
The article below relating to How to Install a Bathtub is exceedingly engaging. You should investigate for yourself.
Mounting a bath tub isn't precisely rocket science, but it does require solid plumbing, carpentry, and sometimes, tiling abilities. Replacing an old bathtub with a new one is likewise a reasonably challenging project. If the old bathtub is conveniently accessible, the job can relocate quickly; if you have to open up a wall to get rid of the old tub as well as position the new tub, the task is a lot harder. In either case, the job is within a home handyman's skills, although you will certainly require a helper to leave the old bathtub and set in the brand-new one. See to it you have actually qualified yourself for the job and fit trying it. Instead of employing a specialist to take control of a halfway-completed task, it is much better to consider utilizing one prior to you start. Chances are you may require an expert plumber to make tube links.
This short article will help you install a new tub in your washroom if you have actually currently purchased a new bathtub and don't require to transform the setup of your previous supply of water pipes.
Your devices and product list need to comprise the following:
Planning for the Setup
Firstly, the supporting frame supplied with the bath must be fitted (if called for) according to the maker's directions. Next, fit the faucets or mixer to the bath tub. When fitting the tap block, it is very important to make certain that if the tap features a plastic washer, it is fitted in between the bathroom as well as the faucets. On a plastic bath, it is additionally practical to fit a supporting plate under the taps unit to stop pressure on the bath tub.
Fit the adaptable faucet connectors to the bottom of both taps utilizing 2 nuts and also olives (sometimes provided with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and after that pass the electrical outlet via the hole in the bathroom. Use the nut supplied by the supplier to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the versatile overflow pipe to the overflow outlet. Afterwards, screw the pipeline to the overflow face which ought to be fitted inside the bathroom. See to it you make use of all of the supplied washers.
Attach the catch to the bottom of the waste outlet on the bathtub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the catch to the outlet. Connect the bottom of the overflow tube in a comparable manner.The bath ought to now be ready to be suited its last placement.
Removing Old Touches
If you need to change old taps with brand-new ones as a part of your installment, after that the first thing you must do is detach the supply of water. After doing so, activate the faucets to drain pipes any water continuing to be in the system. The procedure of getting rid of the existing faucets can be fairly problematic as a result of the restricted access that is often the instance.
Utilize a container wrench (crowsfoot spanner) or a tap device to reverse the nut that attaches the supply pipelines to the faucets. Have a towel ready for the remaining water that will come from the pipes. As soon as the supply pipes have actually been eliminated, use the exact same tool to loosen the nut that holds the faucets onto the bath/basin. You will need to stop the solitary faucets from transforming during this process. As soon as the faucets have been removed, the holes in the bath/basin will certainly have to be cleaned of any type of old securing substance.
Prior to going on to fit the brand-new taps, contrast the pipeline links on the old faucets to the new faucets. If the old taps are longer than the brand-new taps, after that a shank adapter is required for the brand-new faucets to fit.
Mounting the Tub
Using the two wooden boards under its feet, place the bathtub in the called for placement. The wood boards are useful in uniformly spreading out the weight of the tub over the location of the boards as opposed to concentrating all the weight onto four small points.
The following goal is to guarantee that the bath tub is leveled all round. This can be attained by checking the level and also changing the feet on the bath tub until the level reviews level.
To set up faucets, fit all-time low of the furthest versatile tap port to the ideal supply pipe by making a compression join; after that do the exact same for the various other faucet.
Activate the water and examine all joints and new pipework for leakages as well as tighten them if needed. Fill up the bath tub as well as also inspect the overflow electrical outlet as well as the normal electrical outlet for leakages.
Finally, take care of the bathroom paneling as defined in the producer's instruction manual. Tiling as well as securing around the tub needs to wait till the tub has been made use of at the very least once as this will certainly settle it into its last placement.
Fitting New Touches
If the tails of the brand-new taps are plastic, after that you will require a plastic connector to avoid damage to the thread. One end of the port fits on the plastic tail of the tap as well as the other end gives a connection to the current supply pipelines.
If you need to fit a monobloc, after that you will call for lowering couplers, which attaches the 10mm pipe of the monobloc to the common 15mm supply pipeline.
Next off, place the faucet in the mounting opening in the bath/basin making certain that the washers remain in place between the faucet and the sink. Protect the faucet in place with the supplier offered backnut. When the tap is firmly in place, the supply pipelines can be attached to the tails of the taps. The taps can either be connected by utilizing corrugated copper piping or with normal faucet connectors. The former kind must be linked to the tap finishes first, tightening just by hand. The supply pipelines can later on be attached to the various other end. Tighten up both ends with a spanner after both ends have been linked.
Tiling Around the Bath tub
In the area where the bath meets the floor tile, it is essential to secure the accompanies a silicone rubber caulking. This is important as the fitting can move sufficient to break a rigid seal, causing the water to penetrate the wall between the bath and the tiling, bring about problems with moisture and also possible leakages to the ceiling below.
You can pick from a selection of coloured sealants to blend in your components as well as fittings. They are offered in tubes and also cartridges, and also can securing gaps approximately a size of 3mm (1/8 inch). If you have a larger gap to load, you can fill it with twists of soaked paper or soft rope. Remember to always fill up the bathtub with water prior to securing, to allow for the movement experienced when the bathtub remains in use. The sealer can split rather early if you do not consider this motion prior to securing.
Conversely, ceramic coving or quadrant floor tiles can be utilized to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and also reduce to size, are likewise conveniently readily available on the market. It is recommended to fit the ceramic tiles using waterproof or water resistant adhesive and cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
As a fervent person who reads about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround, I imagined sharing that excerpt was really useful. Sharing is caring. Helping others is fun. Bless you for your time. Don't hesitate to check up our blog back soon.
Contact for quality! Report this page